
Flight jacket knit cuffs and waistbands wear out years before the leather does, and replacing them brings a tired A-2 or G-1 back into service. The job is to remove the old knit at the seam where it meets the leather, cut the new waistband to length, and stitch the new knit in evenly. Some owners do it themselves on a machine that sews leather; most hand it to a leather repair shop along with the right kit.
How to Tell When the Knit Is Done

The knit is done when it stops gripping. A cuff that hangs open at the wrist lets wind run up the sleeve on the bike, and a waistband that has lost its stretch lets the jacket ride up and flap. Those two failures matter more to a rider than the cosmetic ones.
Look for these signs:
- Cuffs that stay stretched open after you pull your hand out.
- Holes, runs or frayed edges where the knit rubs a glove cuff or the tank.
- A waistband that no longer pulls in at the hip.
- Heavy pilling or moth damage on wool knit.
If the leather is still sound, worn knit is a repair, not a reason to replace the jacket. Our repair vs replace guide covers how to judge the leather itself.
Match the Kit to Your Jacket
The A-2 and the G-1 use different knit, so start by matching the kit to the jacket. The Flight Jacket Replacement Cuff and Waistband Kit is $37.99 and comes in two versions, each made in the USA to current US Department of Defense military spec, with two one-piece flared cuffs and a waistband you cut to length.
A-2 Kit
The A-2 version is Pil-Trol, a pill-resistant knit of 76% acrylic, 17% polyester and 7% spandex. The waistband is 8 inches unfolded by 44 inches long, the cuffs and waistband are dual layer, and it fits A-2 jackets up to a size 52 chest. Pill-resistant knit suits a rider, because the cuffs rub against glove gauntlets on every ride.
G-1 Kit
The G-1 version is 98% wool and 2% spandex, which the listing describes as naturally flame retardant. The waistband is 9 inches unfolded by 38 inches long. It fits G-1 jackets up to size 52, or an A-2 up to size 50. Both kits replace sleeve cuffs up to 4 inches and come in brown.
Check what is on your jacket now before ordering. Some modern G-1 jackets, such as the Legendary Hellcat G-1, use acrylic knit rather than wool, so matching the existing material keeps the look consistent.
What the Replacement Involves, Step by Step
Replacing knit is a sewing job through leather and lining, and it rewards patience more than speed. Here is what a leather repair shop or a confident home sewer does:
- Photograph and measure the old knit. Note how far the cuff extends past the leather and where the waistband ends meet the zipper.
- Open the seam. Unpick the stitching where the knit joins the sleeve and the hem. On most flight jackets the lining is caught in the same seam, so mark how it sits before you separate it.
- Cut the waistband to length. Lay the new waistband against the old one, add a little for the seam allowance at each end, and cut. The kit waistband is long so it can be cut to fit.
- Pin evenly. Knit is smaller than the leather opening. Quarter-mark both the knit and the opening and pin at the marks, so the stretch is spread evenly instead of bunched on one side.
- Stitch it in. Sew through leather, knit and lining together, stretching the knit to match the leather as you go. A machine that handles leather and a leather needle make this far easier.
- Finish the waistband ends. Fold the ends neatly where they meet the zipper tape and stitch them down so they will not fray.
Do It Yourself or Use a Repair Shop
Do it yourself if you have a machine that sews leather and you have rebuilt a seam before. Use a leather repair shop if your jacket is horsehide or heavy cowhide, if it is a collectible, or if you only have a domestic machine. Bringing the correct kit to the shop saves them sourcing military-spec knit and keeps the result faithful to the original.
Either way, clean and condition the leather while the jacket is apart. Our guide to cleaning a leather flight jacket covers that part of the job.
Keeping New Knit Tight Longer
New knit lasts longest when it is not stretched over glove cuffs every time you ride. Tuck a short-wrist glove under the jacket cuff, or wear a gauntlet over it, rather than forcing the knit over a bulky glove. Hang the jacket on a wide hanger so the waistband is not pulled down by the weight of the leather.
A flight jacket with sound leather and fresh knit has years left in it. Browse our A-2 leather flight jackets to see how the cuffs and waistband should sit on a jacket in good condition, including the Legendary Flying Fortress A-2, which uses Pill-Trol cuffs and waistband.
For background on the jackets these cuffs were designed for, the National Museum of the United States Air Force publishes a fact sheet on WWII aviator jackets.
Frequently Asked Questions
- Can you replace the knit cuffs on a leather flight jacket?
- Yes. The knit cuffs and waistband are sewn into the seam where they meet the leather, so they can be removed and replaced while the leather stays in service. A replacement kit with two cuffs and a waistband cut to length is the usual approach. Many owners take the jacket and the kit to a leather repair shop, since the seam often runs through the lining too.
- What knit is used on A-2 and G-1 flight jackets?
- Our replacement kits use Pil-Trol, a pill-resistant blend of 76% acrylic, 17% polyester and 7% spandex, for the A-2, and 98% wool with 2% spandex for the G-1. Both are made in the USA to current Department of Defense military spec. Some modern G-1 style jackets use acrylic knit instead of wool, so check your jacket before ordering.
- How much does it cost to replace flight jacket cuffs?
- The Legendary USA replacement kit is $37.99 for either the A-2 or G-1 version, based on our store price checked November 21, 2026. Labor is separate if a leather repair shop does the sewing, and shop rates vary by region and by how much of the lining has to be opened. Ask for a quote with the kit in hand.
- Will a replacement kit fit my flight jacket size?
- The A-2 kit fits A-2 jackets up to a size 52 chest. The G-1 kit fits G-1 jackets up to size 52, or an A-2 up to size 50. Both replace sleeve cuffs up to 4 inches. The waistband comes long, 44 inches on the A-2 kit and 38 inches on the G-1 kit, so it can be cut to your jacket.
- How do I make new knit cuffs last longer?
- Avoid stretching them over bulky gloves on every ride. Tuck a short-wrist glove under the knit cuff, or wear a gauntlet over the outside, so the cuff is not forced open. Store the jacket on a wide hanger so the waistband is not pulled down by the leather, and keep wool knit somewhere dry and away from moths.





