
To measure for motorcycle chaps, you need three numbers: your waist measured over your pants, your thigh at its thickest point, and your inseam from the crotch to about an inch above the floor. Take all three with a soft tape that is snug but not tight, wearing the pants and boots you ride in. The thigh is the measurement that matters most, because it is the one part of a chap that cannot be adjusted later.
Here is how to take each measurement, how to read the size chart, and what to do when your numbers land in two different sizes.
What You Need Before You Start

Get a soft cloth tape measure and a second person if you can. Measuring your own thigh and inseam alone is possible, but a helper keeps the tape level and gets a truer number.
Wear the pants you will ride in under the chaps. Chaps are measured over your pants, not over bare skin, because they have to fit over denim or lined riding pants. If you ride in boots, wear them for the inseam measurement. Write each number down as you go.
Step 1: Measure Your Waist Over Your Pants
Wrap the tape around your waist where your belt sits, over your pants, comfortably snug and not tight. For most riders the result is their jeans waist size plus about 2 inches. That extra room is what lets the chaps sit over denim without binding.
If you plan to wear lined pants or long underwear under your chaps in winter, measure over that layer. The waist on our Bad Ass Leather Motorcycle Chaps adjusts with a belt and a laced back panel, so you have some room either way, but it is better to start from the layer you actually ride in.
Step 2: Measure Your Thigh at the Thickest Point
Measure around the thickest part of your upper thigh, right up at the crotch. Keep the tape level and do not pull it tight. This is the measurement the size chart calls very important, and it is the one riders most often skip.
The thigh matters because a chap is a closed tube of leather from the zipper up. When you sit on the bike and bend your knees, your thigh gets wider, and a chap cut too tight there pulls and binds. Unlike the waist, there is no belt or lacing at the thigh to adjust.
Step 3: Measure Your Inseam in Your Riding Boots
Stand straight in your riding boots and measure from the crotch down the inside of the leg to where you want the chaps to end. The standard length is about an inch above the floor. Allow extra inseam length if you ride in boots, because the chap needs to reach over the boot shaft.
Chaps ride up when you sit and your knees bend. A chap that looks right standing in the garage can end above the boot on the highway and leave a cold gap at the ankle, so lean long rather than short.
How to Read the Chaps Size Chart
Compare your three numbers to the standard chart for the Bad Ass Chaps. These are the standard men's chart sizes; the chaps are custom-made to your measurements.
| Size | Waist | Thigh | Inseam |
|---|---|---|---|
| XS | 31 in | 21 in | 30 in |
| S | 32.5 in | 22 in | 31.5 in |
| M | 34 in | 23 in | 32 in |
| L | 39 in | 25.5 in | 34 in |
| XL | 44 in | 27.5 in | 35 in |
| 2XL | 50 in | 29.5 in | 36 in |
Because the chaps are custom-made, have all three numbers ready when you order. If anything about sizing is unclear on the product page, contact us before you order rather than guessing. Our leather motorcycle chaps buying guide covers leather weight and construction if you are still choosing a pair.
Thigh vs Waist: Which Measurement Wins
When your waist and thigh point to different sizes, let the thigh decide. The waist on the Bad Ass Chaps adjusts with a belt and laced back panel. The thigh does not adjust at all.
- Size by thigh: the leg fits in the riding position, and you take the waist in with the lacing. This is the better fit on the bike.
- Size by waist: the belt sits neatly, but a thigh that is too tight binds every time you sit and bend your knees.
Riders with muscular legs and a trim waist run into this most often. Size up for the thigh and use the lacing to finish the waist.
Common Measuring Mistakes
Most chaps that fit badly were measured badly. These are the mistakes we see most often.
- Measuring over bare skin. Chaps go over pants. Measure over the pants you ride in.
- Pulling the tape tight. Snug, not tight. A tight tape gives you a chap that pinches.
- Skipping the thigh. Waist and inseam alone do not size a chap.
- Measuring the inseam barefoot. Wear your riding boots, and allow extra length for them.
Checking the Fit When They Arrive
Put the chaps on over your riding pants and sit on the bike. The thigh should be snug without pinching when your knees are bent, the waist should close with room left in the lacing, and the leg should still reach over your boot in the riding position. Heavy cowhide feels stiff at first and softens over the first several rides, so judge the fit, not the stiffness.
Both colors use the same chart. The Bad Ass Chaps in Brown build a patina at the knees over time, and every pair we carry is in our leather chaps collection. Hang them on a wide hanger between rides, as our guide on how to store leather motorcycle gear explains, and they will hold their shape. Take three careful measurements, trust the thigh, and the chaps will fit the way you ride.
For riders building out a full set of cold-weather gear, the Motorcycle Safety Foundation publishes rider training and gear guidance.
Frequently Asked Questions
- How do I measure my waist for motorcycle chaps?
- Measure your waist over the pants you will wear under the chaps, with the tape comfortably snug but not tight. For most riders that number is their jeans waist size plus about 2 inches, which leaves room for the chaps to sit over denim. If you plan to wear lined pants or long underwear under your chaps in winter, measure over that layer instead.
- Where do you measure the thigh for chaps?
- Measure around the thickest part of your upper thigh, right up at the crotch. This is the most important measurement for chaps, because the thigh cannot be adjusted after the chaps are made. A chap that is too tight at the thigh pulls and binds when you sit on the bike and bend your knees, even if the waist fits well.
- How long should motorcycle chaps be?
- Measure the inseam from the crotch to the length you want the chaps to end, which is usually about an inch above the floor when you stand. Allow extra inseam length if you ride in boots, because the chaps need to reach down over the boot shaft. Chaps that are too short ride up past the boot when you sit on the bike and leave a cold gap at the ankle.
- What if my waist and thigh measurements fall in different sizes?
- Let the thigh decide. On the Legendary Bad Ass Chaps the waist adjusts with a belt and a laced back panel, but the thigh does not adjust at all. Choosing the size that fits your thigh, then taking the waist in with the lacing, gives a better fit on the bike than choosing by waist and living with a tight leg.
- Do leather chaps stretch after you buy them?
- Leather gives a little as it breaks in, mostly at the knee and where the chap bends in the riding position. It does not add a full size. Heavy 1.6 to 1.8mm cowhide like the Bad Ass Chaps starts stiff and softens over the first several rides. If chaps pinch at the thigh when you sit after a few weeks of riding, they are the wrong size.





